Glossary · 82 terms

Roofing glossary

Every word a roofer, an estimate or an inspector might use, explained in plain English, with where you will hear it and where to read more.

5.0 on Google from 83 reviews GAF Master Elite® roofer

Start with the roof

Point at a part, get the word

Most roofing words name a part of the roof. Tap a number on the drawing to jump to what it is and why it matters.

  1. 1Ridge vent
  2. 2Shingles
  3. 3Underlayment
  4. 4Ice and water barrier
  5. 5Roof deck
  6. 6Drip edge
  7. 7Gutter
  8. 8Soffit vent
  9. 9Rafters
  10. 10Chimney flashing
Cutaway of a pitched roof The layers of a shingle roof from the outside in: shingles, underlayment, ice and water barrier and the roof deck on the rafters, with the ridge vent, drip edge, gutter, soffit vent and chimney flashing marked. Ridge vent 1 Shingles 2 Underlayment 3 Ice and water barrier 4 Roof deck (sheathing) 5 Drip edge 6 Gutter 7 Soffit vent 8 Rafters 9 Chimney flashing 10

82 terms

#

Shingles and materials 3-tab shingles

Thin, flat, single-layer shingles with three tabs per strip. Found on older roofs; they typically last 15 to 20 years and lift in wind sooner.

At the inspectionHow long a roof lasts →

A

Roof problems Algae streaks Also called Black streaks

Dark streaks on shingles, mostly on shaded slopes. Mostly cosmetic, unlike moss, which holds water and lifts shingles.

On the roof

Shingles and materials Architectural shingles Also called Dimensional shingles, Laminated shingles

Thick, layered asphalt shingles with a dimensional look. The standard on Staten Island houses today, typically lasting 20 to 30 years in New York weather.

On the estimateAsphalt shingle roofs →

Roof problems Attic condensation

Moisture or frost on the underside of the roof deck, from warm, wet house air meeting a cold roof. Usually a ventilation problem, not a leak.

In the atticAttic ventilation →

Ventilation and gutters Attic fan Also called Power vent

A powered fan, often on a thermostat, that pulls hot air out of the attic in summer.

In the atticAttic fans →

B

Roof problems Blistering

Bubbles in shingles or a flat-roof membrane from trapped moisture or air. On flat roofs they can split open.

At the inspection

Roof problems Blow-off Also called Wind damage

Shingles torn off by wind, usually because their sealant strips have aged out. One area is a repair; tabs going in every storm points to replacement.

At the inspectionStorm damage repair →

Estimates and warranties Bundle

The packs shingles come in. For most architectural shingles three bundles cover one square, and estimates add some extra for cutting waste.

On the estimateRoof cost calculator →

C

Estimates and warranties Change order

A written change to the agreed scope and price, signed before the extra work is done: for example, more rotted decking than the estimate allowed for.

On the estimateHow to read a roofing estimate →

Parts of the roof Chimney crown

The concrete or mortar cap on top of a brick chimney. Cracks in it let water into the chimney, which then shows up as a leak at the roof joint.

On the roofFlashing and chimney repair →

Parts of the roof Coping

The metal or stone cap along the top of a parapet wall that keeps water out of the wall.

On the roof

Parts of the roof Counter-flashing Also called Cap flashing

Metal set into the chimney or wall that laps down over the step flashing, so water cannot get behind it.

On the roof

Flat roofs Cover board

A thin, hard board laid over the insulation of a flat roof, giving the membrane a solid surface to attach to.

On the estimate

Parts of the roof Cricket Also called Saddle

A small peaked section built behind a chimney so water runs around it instead of pooling against it.

On the roof

Roof problems Curling Also called Cupping

Shingle edges turning up as the shingles dry out with age and sun. Usually shows on the sunny slope first.

At the inspectionSigns you need a new roof →

D

Roof problems Deck rot

Soft, rotted roof boards from a long-term leak or a damp attic. Rot in several places means replacement work.

In the atticRepair or replace →

Estimates and warranties Decking allowance

How an estimate prices rotted boards found after tear-off, ideally per sheet. Without a per-sheet price, "decking as needed" can grow the bill.

On the estimateHow to read a roofing estimate →

Estimates and warranties Deposit

Money paid before work starts, usually toward materials. The amount and when it is due should be written on the estimate; be wary of a large cash deposit before any materials arrive.

On the estimateHow to read a roofing estimate →

Estimates and warranties Disposal Also called Haul-away, Dumpster

Hauling the old roof away. A complete estimate includes it, along with daily clean-up and a magnetic sweep of the yard and driveway for nails.

On the estimateHow to read a roofing estimate →

Parts of the roof Dormer

A structure that sticks out of a sloped roof, with its own small roof and a window. Common on capes. The joints where dormers meet the roof need careful flashing.

On the roof

Parts of the roof Drip edge

An L-shaped metal strip along the eaves and rakes. It steers water into the gutter instead of letting it run behind it and rot the fascia.

On the estimateHow to read a roofing estimate →

E

Parts of the roof Eaves Also called Eave edge

The lower edges of the roof, where the gutters hang. Ice dams form here in winter.

On the roof

Flat roofs EPDM Also called Rubber roof

A black synthetic rubber membrane for flat roofs. It stays flexible in cold weather and is simple to patch. Typically lasts 20 to 30 years.

On the estimateEPDM roofing →

F

Parts of the roof Fascia

The board along the roof edge that the gutters are fastened to. Clogged gutters rot it over time.

At the gutterGutters →

Parts of the roof Flashing

Metal that seals the joints where the roof meets something else: a chimney, a wall, a skylight or a vent. Most leaks start at flashing.

On the roofFlashing and chimney repair →

Estimates and warranties Free inspection

Our look at the roof and attic, with photos and a written price, for a repair or a new roof. A written inspection report for a home sale is a separate, paid service.

At the inspectionRoof inspection →

G

Parts of the roof Gable

The triangular wall at the end of a roof with two slopes. Many Staten Island capes and colonials have gable ends.

On the roof

Estimates and warranties GAF Master Elite

GAF’s top contractor certification, held by fewer than 2% of roofing contractors. It lets a contractor offer GAF’s strongest warranties.

On the estimateAbout ProLine →

Shingles and materials GAF Timberline

GAF’s line of architectural shingles, such as Timberline HDZ. A good estimate names the brand, product line and color like this, not just “architectural shingles”.

On the estimateRoof replacement →

Roof problems Granule loss Also called Bald spots

Bald, smooth patches where the granules have washed off and the asphalt is exposed. A sign the shingles are near the end.

At the inspectionSigns you need a new roof →

Shingles and materials Granules

The coarse, sand-like coating on asphalt shingles that shields the asphalt from the sun. Piles of them in the gutters mean the shingles are wearing out.

At the gutterSigns you need a new roof →

Ventilation and gutters Gutter guard Also called Leaf guard

A screen or cover over the gutter that keeps leaves out while letting water in. Useful under heavy tree cover.

At the gutterGutter guards →

H

Parts of the roof Hip

The sloped ridge where two roof planes meet on an outside corner. A hip roof slopes down on all four sides.

On the roof

Estimates and warranties Home Improvement Contractor licence Also called HIC licence

The licence New York City requires of contractors doing home improvement work. Ours is 2120969-DCWP; look any contractor up in the city’s licence records.

On the estimateAbout ProLine →

I

Shingles and materials Ice and water barrier Also called Ice and water shield, Leak barrier

A self-adhesive rubberized membrane laid at the eaves, in valleys and around chimneys and skylights. It seals around nails, so water backed up by ice dams cannot get in.

On the estimateHow to read a roofing estimate →

Roof problems Ice dam

A ridge of ice at the eaves. Heat from the house melts snow higher up; the water refreezes at the cold edge and backs up under the shingles. Fixed with ventilation and ice and water barrier.

At the gutterAttic ventilation →

Ventilation and gutters Intake and exhaust

The two halves of attic ventilation: fresh air in low (soffits), warm air out high (ridge or roof vents). A roof needs both, roughly balanced.

In the atticAttic ventilation →

K

Parts of the roof Kick-out flashing Also called Diverter flashing

An angled piece of flashing at the bottom of a roof-to-wall joint that turns water into the gutter instead of letting it run down the wall behind the siding.

At the inspectionRoof repair →

L

Ventilation and gutters Leader Also called Downspout

The New York word for a downspout: the pipe that carries water from the gutter down to the ground or a drain.

At the gutterGutters →

Estimates and warranties Low-slope

A roof with very little pitch. Shingles need a minimum slope to shed water, so roofs flatter than that need a membrane such as TPO or EPDM.

At the inspectionFlat roofing →

M

Estimates and warranties Manufacturer warranty

The material maker’s warranty on the products. As GAF Master Elite contractors we can offer up to a 50-year GAF warranty on GAF shingles.

On the estimateRoof replacement →

Flat roofs Modified bitumen Also called Mod bit, Torch-down

Asphalt-based rolled roofing, torched or adhered in overlapping layers. Common on older flat roofs; it typically lasts 15 to 20 years.

At the inspectionFlat roof materials compared →

N

Roof problems Nail pop

A roofing nail that has backed up out of the deck and lifted the shingle above it, leaving a path for water.

At the inspection

Shingles and materials Nailing line Also called Nailing zone

The marked strip on each shingle where the nails go. Nails placed above or below it are a common reason shingles blow off.

On the roofStorm damage repair →

O

Parts of the roof Open and closed valleys Also called Valley metal, Woven valley

Two ways to finish a valley. An open valley is lined with metal and the shingles are cut back so the metal shows; a closed valley is covered by shingles cut or woven across it.

On the estimate

Parts of the roof Overhang

The part of the roof that reaches past the walls, so rain falls clear of the house. Its underside is the soffit and its outer edge the fascia.

On the roof

P

Parts of the roof Parapet

A low wall around the edge of a flat roof, common on attached houses and row houses. The joint between the roof and the parapet is a frequent leak point.

On the roofFlat roofing →

Parts of the roof Penetration

Anything that passes through the roof: plumbing vents, chimneys, skylights, exhaust fans. Each one needs its own flashing, and each one is a possible leak point.

At the inspectionRoof leak repair →

Parts of the roof Pipe boot Also called Vent boot, Pipe collar

The rubber-sealed collar around a plumbing vent pipe. The rubber cracks with age and sun, and it is one of the most common small leaks.

At the inspectionRoof leak repair →

Estimates and warranties Pitch Also called Slope

How steep a roof is, written as the rise in inches over 12 inches of run: 6/12 means it rises 6 inches every foot. Steeper roofs take longer and cost more.

On the estimateRoof cost →

Roof problems Ponding

Water still standing on a flat roof about two days after the rain stops. It wears out any membrane fast and finds every weak seam.

On the roofFlat roofing →

R

Ventilation and gutters Rafter baffle Also called Insulation baffle, Vent chute

A channel fitted between rafters at the eaves that keeps insulation from blocking the soffit vents.

In the attic

Parts of the roof Rafters Also called Trusses

The sloped framing members that carry the roof deck. Pre-built triangular versions are called trusses.

In the attic

Parts of the roof Rake Also called Rake edge

The sloped edge of a roof at the gable end, running from the eaves up to the ridge.

On the roof

Parts of the roof Ridge

The peak of the roof, where two slopes meet at the top. A ridge line that dips in the middle points to a problem with the deck or framing below.

On the roofSigns you need a new roof →

Parts of the roof Ridge cap Also called Hip and ridge shingles

The thick, folded shingles that cover the ridge and hips. They take the most wind of any shingle on the roof.

On the estimate

Ventilation and gutters Ridge vent

A low vent running along the ridge that lets hot, damp air out of the attic. It works with soffit vents, which let fresh air in.

On the roofRoof vents →

Flat roofs Roof coating

A liquid layer rolled or sprayed over a sound flat roof to seal it and add years. It is not a new roof, and it only works over a dry, well-attached one.

On the estimateFlat roof coatings →

Parts of the roof Roof deck Also called Decking, Sheathing

The boards or plywood the roof is nailed to. Rotted sections are found and replaced once the old shingles are off.

In the atticHow to read a roofing estimate →

Flat roofs Roof drain

A drain set into the low point of a flat roof, clamped to the membrane. A blocked drain is the main cause of ponding.

On the roof

Estimates and warranties Roof-over Also called Layover, Overlay

New shingles installed over the old layer instead of a tear-off. Cheaper today, but it hides rotted decking, traps heat and makes the next roof harder.

On the estimateRepair or replace →

S

Estimates and warranties Scope of work

The part of an estimate that says exactly what will be done, with what, and where. Compare scopes line by line, not just totals.

On the estimateHow to read a roofing estimate →

Flat roofs Scupper

An opening through a parapet wall that lets water drain off a flat roof, usually into a leader.

At the gutterFlat roofing →

Shingles and materials Sealant strip

The line of adhesive on each shingle that bonds it to the one below once the sun warms it. In cold weather shingles may need sealing by hand.

On the roof

Flat roofs Seam

Where two sheets of membrane overlap and join. On TPO they are welded; on EPDM glued or taped. Open seams are a common flat-roof leak.

At the inspection

Ventilation and gutters Seamless gutter

A gutter formed on site from one continuous piece of metal, with no joints along the run to leak.

At the gutterGutter installation →

Shingles and materials Shingle exposure Also called Reveal

The part of each row of shingles left showing once the next row covers the rest. The manufacturer sets it; uneven rows are a sign of a careless install.

At the inspection

Parts of the roof Skylight curb

The raised frame a skylight sits on. Its flashing is what keeps water out around the skylight.

On the roofSkylights →

Parts of the roof Soffit

The underside of the roof overhang, between the fascia and the wall. Vented soffits let fresh air into the attic.

At the gutterAttic ventilation →

Ventilation and gutters Soffit vent Also called Intake vent

Vents in the underside of the roof overhang that let outside air into the attic. Insulation blocking them is a common cause of a hot, damp attic.

At the gutterAttic ventilation →

Estimates and warranties Square

The unit roofs are measured and priced in: 100 square feet of roof surface. A 2,000 square foot roof is 20 squares.

On the estimateRoof cost calculator →

Shingles and materials Standing seam metal

Metal roof panels joined by raised seams. Typically lasts 40 years or more; the fasteners and flashing need attention before the panels do.

On the estimateMetal roofing →

Shingles and materials Starter strip Also called Starter shingles

The first row of shingles along the eaves and rakes, with a sealant strip that holds the first course down in wind.

On the estimate

Parts of the roof Step flashing

Small L-shaped pieces of metal woven in with each row of shingles where a roof meets a wall or the side of a chimney.

On the roof

T

Flat roofs Tapered insulation

Insulation boards cut with a built-in slope, laid under a flat roof membrane so water runs to the drains instead of pooling.

On the estimateFlat roofing →

Estimates and warranties Tear-off

Removing the old roof down to the deck before the new one goes on. The estimate should say how many layers come off.

On the estimateHow to read a roofing estimate →

Flat roofs TPO Also called Thermoplastic polyolefin

A white single-ply membrane for flat roofs, with seams welded together by hot air. It reflects summer heat and typically lasts 20 to 30 years.

On the estimateTPO roofing →

Ventilation and gutters Turbine vent Also called Whirlybird

A round, spinning roof vent that turns in the wind to draw air out of the attic.

On the roof

U

Shingles and materials Underlayment Also called Synthetic underlayment, Felt paper, Tar paper

The water-resistant sheet laid over the whole deck before the shingles: the second line of defense. Synthetic underlayment has largely replaced felt paper.

On the estimateHow to read a roofing estimate →

V

Parts of the roof Valley

The V-shaped channel where two roof slopes meet on an inside corner. Valleys carry a lot of water, so they get ice and water barrier underneath and careful shingling.

On the roofRoof repair →

W

Shingles and materials Wind rating

The wind speed a shingle is tested and warranted to resist, often higher when it is installed with extra nails. Worth asking about on exposed streets near the water.

On the estimate

Estimates and warranties Workmanship warranty

The roofer’s own warranty on the installation. Ours is up to 30 years, written on the estimate.

On the estimateRoof replacement →

Free estimate

Heard a word you want explained on your own roof?

  1. We call you back
    Usually the same day, to book a time that suits you.
  2. We come to you
    The owner inspects at your home, photographs what he finds and shows you.
  3. You get a written price
    Free, with no obligation. The exact figure, on paper.

Rather talk? Call (347) 323-9128. Open 24/7 for leaks.

Tell us about your roof

Four quick answers. We call you back, usually the same day.

Enter your name.
Enter a 10-digit phone number.
Enter a 5-digit ZIP code.

We use your details only to call you about this estimate. Privacy policy

Free estimate

Three quick steps

What do you need?
Where is the roof?

We cover every Staten Island ZIP.

Where do we call you back?
Enter your name.
Enter a 10-digit phone number.

Free, no obligation. We call you back, usually the same day. Privacy

Rather talk? (347) 323-9128